亚洲欧美国产精品专区久久,一卡一卡三卡四卡不卡乱码在线观看,无码国产伦一区二区三区视频,疯狂 喷水爽www噜噜噜,国产精品日老太婆

電梯門套無接縫翻新是現在建材行業一種新型技術，這種技術相對要節省時間，而且相對成本較低，下面濟南皓暉建材的小編就給大家講解一下：
Elevator door without joint renovation is now building materials industry a new technology, the technology relative to save time, and relatively low cost, the following Jinan Hao Hui building materials Xiaobian is for everyone to explain:
1、先將電梯門套縫隙間原有填充物清理干凈，然后使用專用的電梯門套開縫機對原來電梯門套安裝的中縫重新整齊切割開縫，使石材間的縫隙的寬度差降至最低，再用接近電梯門套顏色的石膠對其進行填補。
1, first elevator door gap between the original filler to clean up, and then use special elevator door slot machine of original elevator door installation of raphe to neat cutting slot, so that the width of the gap between the stone to minimize the error, and then close the elevator door color of stone glue to fill.
2、使用接近電梯門套本身顏色的石膠并將石膠進行完美的調色，使之充分接近原來電梯門套的顏色來提高整體感，達到最理想的視覺效果。
2, the use of close to the color of the elevator door itself of stone glue and glue stone perfect color, to fully close to the color of the original elevator door to enhance the overall sense, to achieve the best visual effects.
3、將調好的石膠進行填充，由于石膠完全凝固后會有一定程度的收縮，所以應使石膠稍微高于電梯門套水平面，這樣不至于多次填充。
3, will adjust the good of stone glue fill, because of stone glue completely solidified will have a certain degree of contraction, it should be made of stone glue is slightly higher than the level of the elevator door, so as not to repeatedly fill.

4、采用打磨拋光片和打磨填充劑，使之與電梯門套成為一個水平面，增加電梯門套整體感，并解決縫隙間高低位問題，防止縫隙再次返黑。使用花崗巖翻新機配合專用剪口研磨片對剪口位進行精心打磨，使其與電梯門套成為一個平面整體。
4, the polishing and grinding filler, to become a horizontal plane and the elevator door, increase the sense of elevator door pocket integral, and solve the gap between high and low problem and prevent the gap again back to black. Using granite face lifting machine with special cutting grinding mouth piece to cut a mouth carefully burnish, make it become a whole plane and the elevator door.
5、研磨拋光：使用專用的花崗巖拋光機，從50-3000號的電梯門套水磨片由粗到細對電梯門套進行研磨，致使地面光亮平整如新。
5, grinding and polishing: use appropriative granite polishing machine from the No. 50 3000 elevator door chip mill from coarse to fine grinding of the elevator door. As a result, surface smooth and bright as new.
6、結晶處理：采用電梯門套結晶粉和結晶藥劑配合晶面打磨機拋光，在打磨重壓下讓電梯門套和結晶粉在高溫作用下發生物理和化學綜合反應，形成一層致密、堅硬的結晶保護層。結晶后能增強色彩和光亮度，還能達到防滑、防水、防油等功效。
6 and crystallization processes: the elevator door crystalline powder and crystallization drug together with crystal surface grinding polishing machine, in burnish weigh for elevator door and crystalline powder physical and chemical reaction occurred under the action of high temperature, form a layer of dense, hard crystalline protection layer. After the crystallization can enhance the color and brightness, but also to achieve non slip, waterproof, anti oil and other functions.